The Quiescent H-mode exhibits H-mode levels of confinement and edge pedestal pressures, but does not exhibit ELMs. To date this mode has only been observed in tokamaks during beam heating with some or all of the beams injected counter to the direction of plasma current. During QH-mode, fast ion loss to the low field side plasma facing surfaces has been observed. Some of the fast ion loss is calculated to be the result of outwardly directed banana orbits of the energetic beam ions created in the edge region. Other fast ion loss has been observed to be associated with bursts or oscillations in broadband, high-frequency, magnetic fluctuations. The relationship of the fast ion loss to the ELM stabilization or edge particle transport during QH-mode is not yet understood. © 2004 Elsevier B.V. All rights reserved.

Measurements show fast ion losses correlated with applied three-dimensional (3D) fields in a variety of plasmas ranging from L-mode to resonant magnetic perturbation (RMP) edge localized mode (ELM) suppressed H-mode discharges. In DIII-D L-mode discharges with a slowly rotating n = 2 magnetic perturbation, scintillator detector loss signals synchronized with the applied fields are observed to decay within one poloidal transit time after beam turnoff indicating they arise predominantly from prompt loss orbits. Full orbit following using M3D-C1 calculations of the perturbed fields and kinetic profiles reproduce many features of the measured losses and points to the importance of the applied 3D field phase with respect to the beam injection location in determining the overall impact on prompt beam ion loss. Modeling of these results includes a self-consistent calculation of the 3D perturbed beam ion birth profiles and scrape-off-layer ionization, a factor found to be essential to reproducing the experimental measurements. Extension of the simulations to full slowing down timescales, including fueling and the effects of drag and pitch angle scattering, show the applied n = 3 RMPs in ELM suppressed H-mode plasmas can induce a significant loss of energetic particles from the core. With the applied n = 3 fields, up to 8.4% of the injected beam power is predicted to be lost, compared to 2.7% with axisymmetric fields only. These fast ions, originating from minor radii ρ > 0.7, are predicted to be primarily passing particles lost to the divertor region, consistent with wide field-of-view infrared periscope measurements of wall heating in n = 3 RMP ELM suppressed plasmas. Edge fast ion Dα (FIDA) measurements also confirm a large change in edge fast ion profile due to the n = 3 fields, where the effect was isolated by using short 50 ms RMP-off periods during which ELM suppression was maintained yet the fast ion profile was allowed to recover. The role of resonances between fast ion drift motion and the applied 3D fields in the context of selectively targeting regions of fast ion phase space is also discussed.

Significant progress in obtaining high performance discharges lasting many energy confinement times in the DIII-D tokamak has been realized in recent experimental campaigns. Normalized performance ∼10 has been sustained for more than 5>E with qmin > 1.5. (The normalized performance is measured by the product βNH89, indicating the proximity to the conventional β limits and energy confinement quality, respectively.) These H mode discharges have an ELMing edge and β < 5%. The limit to increasing β is a resistive wall mode, rather than the tearing modes as previously observed. Confinement remains good despite qmin > 1. The global parameters were chosen to optimize the potential for fully non-inductive current sustainment at high performance, which is a key program goal for the DIII-D facility. Measurement of the current density and loop voltage profiles indicate that ≈75% of the current in the present discharges is sustained non-inductively. The remaining ohmic current is localized near the half-radius. The electron cyclotron heating system is being upgraded to replace this remaining current with ECCD. Density and β control, which are essential for operating advanced tokamak discharges, were demonstrated in ELMing H mode discharges with βNH89 ≈ 7 for up to 6.3 s or ≈34τE. These discharges appear to have stationary current profiles with qmin ≈ 1.05 in agreement with the current profile relaxation time ≈1.8 s.

Fusion power has been increased by a factor of 3 in DIII-D by tailoring the pressure profile to avoid the kink instability in H-mode plasmas. The resulting plasmas are found to have neoclassical ion confinement. This reduction in transport losses in beam-heated plasmas with negative central shear is correlated with a dramatic reduction in density fluctuations. Improved magnetohydrodynamic stability is achieved by controlling the plasma pressure profile width. In deuterium plasmas the highest gain Q (the ratio of fusion power to input power), was 0.0015, corresponding to an equivalent Q of 0.32 in a deuterium-tritium plasma. © 1996 The American Physical Society.

Advanced tokamaks seek to achieve a high bootstrap current fraction without sacrificing fusion power density or fusion gain. Good progress has been made towards the DIII-D research goal of demonstrating a high-β advanced tokamak plasma in steady state with a relaxed, fully non-inductive current profile and a bootstrap current fraction greater than 50%. The limiting factors for transport, stability, and current profile control in advanced operating modes are discussed in this paper.

Joint experiment/theory/modelling research has led to increased confidence in predictions of the pedestal height in ITER. This work was performed as part of a US Department of Energy Joint Research Target in FY11 to identify physics processes that control the H-mode pedestal structure. The study included experiments on C-Mod, DIII-D and NSTX as well as interpretation of experimental data with theory-based modelling codes. This work provides increased confidence in the ability of models for peeling-ballooning stability, bootstrap current, pedestal width and pedestal height scaling to make correct predictions, with some areas needing further work also being identified. A model for pedestal pressure height has made good predictions in existing machines for a range in pressure of a factor of 20. This provides a solid basis for predicting the maximum pedestal pressure height in ITER, which is found to be an extrapolation of a factor of 3 beyond the existing data set. Models were studied for a number of processes that are proposed to play a role in the pedestal ne and Te profiles. These processes include neoclassical transport, paleoclassical transport, electron temperature gradient turbulence and neutral fuelling. All of these processes may be important, with the importance being dependent on the plasma regime. Studies with several electromagnetic gyrokinetic codes show that the gradients in and on top of the pedestal can drive a number of instabilities. © 2013 IAEA, Vienna.