Antibubbles are fluid entities with the inverse phase of regular bubbles. While the structure and stability of antibubbles have been studied, a fundamental understanding of antibubble formation remains limited. We report a theoretical and experimental study of antibubble formation. In the experiment, pairs of surfactant-laden water drops impinged successively on the surface of the same liquid reservoir to create antibubbles. We propose four criteria for antibubble formation from a scaling analysis. Two dimensionless groups prescribe the likelihood of antibubble formation, the summative Weber number and the ratio of timescales between the capillarity driven pinch-off and the viscous drainage of air.

We present a surface-engineering approach that turns all liquids highly wetting, including ultra-high surface tension fluids such as mercury. Previously, highly wetting behavior was only possible for intrinsically wetting liquid/material combinations through surface roughening to enable the so-called Wenzel and hemiwicking states, in which liquid fills the surface structures and causes a droplet to exhibit a low contact angle when contacting the surface. Here, we show that roughness made of reentrant structures allows for a metastable hemiwicking state even for nonwetting liquids. Our surface energy model reveals that with liquid filled in the structure, the reentrant feature creates a local energy barrier, which prevents liquid depletion from surface structures regardless of the intrinsic wettability. We experimentally demonstrated this concept with microfabricated reentrant channels. Notably, we show an apparent contact angle as low as 35° for mercury on structured silicon surfaces with fluorinated coatings, on which the intrinsic contact angle of mercury is 143°, turning a highly nonwetting liquid/material combination highly wetting through surface engineering. Our work enables highly wetting behavior for previously inaccessible material/liquid combinations and thus expands the design space for various thermofluidic applications.

Boiling is an essential process in numerous applications including power plants, thermal management, water purification, and steam generation. Previous studies have shown that surfaces with microcavities or biphilic wettability can enhance the efficiency of boiling heat transfer, that is, the heat transfer coefficient (HTC). Surfaces with permeable structures such as micropillar arrays, in contrast, have shown significant enhancement of the critical heat flux (CHF). In this work, we investigated microtube structures, where a cavity is defined at the center of a pillar, as structural building blocks to enhance HTC and CHF simultaneously in a controllable manner. We demonstrated simultaneous CHF and HTC enhancements of up to 62 and 244%, respectively, compared to those of a smooth surface. The experimental data along with high-speed images elucidate the mechanism for simultaneous enhancement where bubble nucleation occurs in the microtube cavities for increased HTC and microlayer evaporation occurs around microtube sidewalls for increased CHF. Furthermore, we combined micropillars and microtubes to create surfaces that further increased CHF by achieving a path to separate nucleating bubbles and rewetting liquids. This work provides guidelines for the systematic surface design for boiling heat transfer enhancement and has important implications for understanding boiling heat transfer mechanisms.

Wetting functionalities of rough surfaces are largely determined by the Laplace pressure generated across liquid–gas interfaces formed within surface structures. Typically, rough wetting surfaces create negative Laplace pressures, enabling capillary wicking, while rough non-wetting surfaces create positive Laplace pressures, exhibiting fluid repellency. Here, with microfabricated reentrant structures, it is shown that the same surface can exhibit either a negative or positive Laplace pressure, regardless of its intrinsic wettability. This material-independent Laplace pressure duality enables or enhances a range of wetting functionalities including wicking, switchability, and selectivity. On the same surface, capillary rise, capillary dip, and the combination of the two which leads to further enhancement of the total sustainable capillary height and Laplace pressure, the driving force for wicking is demonstrated. Further, active switching of wetting states between the hemiwicking and the repellent Cassie state on reentrant structures is shown. Moreover, with a water-hexane mixture system, selective wetting of reentrant structures are demonstrated, that is, water can be selectively wicked or repelled in the presence of hexane, and vice versa. These functionalities are achieved, which would typically require complex chemical coatings, solely using surface structures, thus largely expanding the design space for a wide range of thermofluidic applications.

Boiling heat transfer is dictated by interfacial phenomena at the three-phase contact line where vapor bubbles form on the surface. Structured surfaces have shown significant enhancement in critical heat flux (CHF) during pool boiling by tailoring interfacial phenomena. This CHF enhancement has been primarily explained by two structural effects: roughness, which extends the contact line length at the bubble base, and wickability, the ability to imbibe liquid through surface structures by capillary pumping. In this work, we show that CHF enhancement on structured surfaces cannot be described by roughness or wickability alone. This result was confirmed using systematically designed micropillar surfaces with controlled roughness and wickability. Further, we performed a scaling analysis and derived a unified descriptor, which represents the combined effects of thin film density and volumetric wicking rate. This unified descriptor shows a reasonable correlation with CHF values with our experiments and literature data. This work provides important insights in understanding the role of surface structures on CHF enhancement, thereby providing guidelines for the systematic design of surface structures for enhanced pool boiling heat transfer.

Boiling is an effective energy-transfer process with substantial utility in energy applications. Boiling performance is described mainly by the heat-transfer coefficient (HTC) and critical heat flux (CHF). Recent efforts for the simultaneous enhancement of HTC and CHF have been limited by an intrinsic trade-off between them-HTC enhancement requires high nucleation-site density, which can increase bubble coalescence resulting in limited CHF enhancement. In this work, this trade-off is overcome by designing three-tier hierarchical structures. The bubble coalescence is minimized to enhance the CHF by defining nucleation sites with microcavities interspersed within hemi-wicking structures. Meanwhile, the reduced nucleation-site density is compensated for by incorporating nanostructures that promote evaporation for HTC enhancement. The hierarchical structures demonstrate the simultaneous enhancement of HTC and CHF up to 389% and 138%, respectively, compared to a smooth surface. This extreme boiling performance can lead to significant energy savings in a variety of boiling applications.

Water scarcity is a particularly severe challenge in arid and desert climates. While a substantial amount of water is present in the form of vapour in the atmosphere, harvesting this water by state-of-the-art dewing technology can be extremely energy intensive and impractical, particularly when the relative humidity (RH) is low (i.e., below ~40% RH). In contrast, atmospheric water generators that utilise sorbents enable capture of vapour at low RH conditions and can be driven by the abundant source of solar-thermal energy with higher efficiency. Here, we demonstrate an air-cooled sorbent-based atmospheric water harvesting device using the metal-organic framework (MOF)-801 [Zr₆O₄(OH)₄(fumarate)₆] operating in an exceptionally arid climate (10-40% RH) and sub-zero dew points (Tempe, Arizona, USA) with a  thermal efficiency (solar input to water conversion) of ~14%. We predict that this device delivered over 0.25 L of water per kg of MOF for a single daily cycle.

Vapor condensation is routinely used as an effective means of transferring heat or separating fluids. Dropwise condensation, where discrete droplets form on the condenser surface, offers a potential improvement in heat transfer of up to an order of magnitude compared to filmwise condensation, where a liquid film covers the surface. Low surface tension fluid condensates such as hydrocarbons pose a unique challenge since typical hydrophobic condenser coatings used to promote dropwise condensation of water often do not repel fluids with lower surface tensions. Recent work has shown that lubricant infused surfaces (LIS) can promote droplet formation of hydrocarbons. In this work, we confirm the effectiveness of LIS in promoting dropwise condensation by providing experimental measurements of heat transfer performance during hydrocarbon condensation on a LIS, which enhances heat transfer by ≈450% compared to an uncoated surface. We also explored improvement through removal of noncondensable gases and highlighted a failure mechanism whereby shedding droplets depleted the lubricant over time. Enhanced condensation heat transfer for low surface tension fluids on LIS presents the opportunity for significant energy savings in natural gas processing as well as improvements in thermal management, heating and cooling, and power generation.

The critical heat flux during pool boiling has been investigated for a range of applications including electrical power generation and thermal management. Reported experimental CHF values during pool boiling of water on flat metallic surfaces, however, show a large discrepancy across studies. Here, we address this discrepancy in CHF values by accounting for oxidation of metallic surfaces during boiling. We studied the effect of in situ oxidation on flat Cu and Ni surfaces by changing the duration that samples were held in saturated water before conducting boiling experiments. The morphology and chemical composition of surfaces after the boiling experiments were analyzed by atomic force microscopy and X-ray photoelectron spectroscopy, respectively. Cu surfaces showed gradually increasing CHF values as the duration in saturated water increased, which could be attributed to the increase in roughness due to the formation of Cu2O nanostructures. Conversely, Ni surfaces showed relatively stable CHF and morphology as a nearly flat layer of NiO formed, with one exception: formation of a highly wetting hydroxide, Ni(OH)2, on a Ni coupon held in saturated water for 24 h resulted in a uniquely high CHF value, signifying the importance of surface chemistry in addition to morphology. The fundamental mechanisms resulting in the wide spread of CHF values on metallic surfaces elucidated in this work will lead to more accurate estimation of CHF as well as a deeper mechanistic understanding of CHF values on engineered surfaces.

Water adsorption is becoming increasingly important for many applications including thermal energy storage, desalination, and water harvesting. To develop such applications, it is essential to understand both adsorbent-adsorbate and adsorbate-adsorbate interactions, and also the energy required for adsorption/desorption processes of porous material-adsorbate systems, such as zeolites and metal-organic frameworks (MOFs). In this study, we present a technique to characterize the enthalpy of adsorption/desorption of zeolites and MOF-801 with water as an adsorbate by conducting desorption experiments with conventional differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). With this method, the enthalpies of adsorption of previously uncharacterized adsorbents were estimated as a function of both uptake and temperature. Our characterizations indicate that the adsorption enthalpies of type I zeolites can increase to greater than twice the latent heat whereas adsorption enthalpies of MOF-801 are nearly constant for a wide range of vapor uptakes.