High-temperature superconductors such as REBa2Cu3O7-x (REBCO, RE = rare earth) can generate strong magnetic fields that are promising for applications in particle accelerators and compact fusion reactors. Traditionally, voltage taps are installed in superconducting magnets to measure the voltage signals due to resistive transitions. The voltage-tap-based diagnostics is important for the development of magnet technology as it can help pinpoint the locations in the magnet windings that limit the magnet performance. The architecture of the multi-tape REBCO cable such as CORC wires, however, makes it difficult to apply the voltage-tap-based diagnostics to identify the locations of resistive transitions. Distributed fiber optic sensing (DFOS) has the potential to address this issue. In this paper, we report the measurements of thermal strain along a CORC wire based on optical frequency domain reflectometry with a maximum spatial resolution of 0.65 mm and a temporal resolution of 10 Hz. The optical fiber is co-wound with the CORC wire that is epoxy impregnated. During the test, current was increased until a resistive transition occurred in the conductor. The spectrum shift of the reflected light along the fiber was recorded. The results suggested that with proper thermal isolation from the cryogen, DFOS can be used to identify the locations of resistive transitions in CORC wires and magnets. The results will allow a better understanding of the causes of resistive transitions in REBCO conductors and magnets, which will help improve the REBCO magnet technology.

ReBCO superconducting cables have the potential to enable compact thermonuclear fusion reactors that operate at magnetic fields exceeding 20 T and allow operation at temperatures far exceeding the boiling point of liquid helium, potentially allowing for demountable magnets. Normal zone detection remains a challenge, and while novel quench detection techniques are an active area of research, few are non-invasive, provide real-time quench detection, and have been demonstrated with current ramp rates relevant for fusion reactors. To address this problem, a CORC® cable termination is developed with integrated Hall sensors to monitor current redistribution as a proxy for quench detection. The methodology exploits the current sharing and layered topology in CORC® cables, and allows quench detection using a localized sensor instead of co-wound voltage wires or optical fibers. Experiments are presented where current redistribution is measured from induced quenches, and in a 0.2 meter CORC® sample it is found that the Hall sensors detect normal zone transitions with a similar magnitude and temporal resolution as voltage measurements. To emulate the conditions of dynamic poloidal and central solenoidal fields, experiments are repeated with ramp rates up to 10 kA s-1 that demonstrate the potential to detect normal zone development over a range of experimental parameters.

Fusion magnets made from high temperature superconducting ReBCO CORC^® cables are typically protected with quench detection systems that use voltage or temperature measurements to trigger current extraction processes. Although small coils with low inductances have been demonstrated, magnet protection remains a challenge and magnets are typically operated with little knowledge of the intrinsic performance parameters. We propose a protection framework based on current distribution monitoring in fusion cables with limited inter-cable current sharing. By employing inverse Biot-Savart techniques to distributed Hall probe arrays around CORC^® Cable-In-Conduit-Conductor (CICC) terminations, individual cable currents are recreated and used to extract the parameters of a predictive model. These parameters are shown to be of value for detecting conductor damage and defining safe magnet operating limits. The trained model is then used to predict cable current distributions in real-time, and departures between predictions and inverse Biot-Savart recreated current distributions are used to generate quench triggers. The methodology shows promise for quality control, operational planning and real-time quench detection in bundled CORC^® cables for compact fusion reactors.

REBa2Cu3Ox (REBCO, RE = rare earth elements) coated conductors can carry high current in high background fields, in principle enabling dipole magnetic fields beyond 20 T. Although model accelerator magnets wound with single REBCO tapes have been successfully demonstrated, magnet technology based on high-current REBCO cables for high-field accelerator magnet applications has yet to be established. We developed a two-layer canted cosθ dipole magnet with an aperture of 70 mm using 30 m long commercial Conductor on Round Core (CORC®) wires. The 3.1 mm diameter CORC® wire contained 16 commercial REBCO tapes with a 30 μm thick substrate. The magnet was tested at 77 and 4.2 K. It generated a peak dipole field of 1.2 T with 4.8 kA at 4.2 K with neither thermal runaway nor training. Reasonable geometric field quality and strong magnetization-current effects with multipole decay were observed. Our work demonstrated a feasible high-temperature superconducting magnet technology as a first step toward a new accelerator magnet paradigm that will enable high-field inserts for next-generation circular colliders and stand-alone magnets that can operate over a wide temperature range for a broad range of applications.

REBCO coated conductors maintain a high engineering current density above 16 T at 4.2 K. That fact will significantly impact markets of various magnet applications including high-field magnets for high-energy physics and fusion reactors. One of the main challenges for the high-field accelerator magnet is the use of multi-tape REBCO cables with high engineering current density in magnet development. Several approaches developing high-field accelerator magnets using REBCO cables are demonstrated. In this paper, we introduce an alternative concept based on the canted cos θ (CCT) magnet design using conductor on round core (CORC®) wires that are wound from multiple REBCO tapes with a Cu core. We report the development and test of double-layer three-turn CCT dipole magnets using CORC® wires at 77 and 4.2 K. The scalability of the CCT design allowed us to effectively develop and demonstrate important magnet technology features such as coil design, winding, joints and testing with minimum conductor lengths. The test results showed that the CCT dipole magnet using CORC® wires was a viable option in developing a REBCO accelerator magnet. One of the critical development needs is to increase the engineering current density of the 3.7 mm diameter CORC® wire to 540 A mm-2 at 21 T, 4.2 K and to reduce the bending radius to 15 mm. This would enable a compact REBCO dipole insert magnet to generate a 5 T field in a background field of 16 T at 4.2 K.

Although the high-temperature superconducting (HTS) REBa2Cu3O x (REBCO, RE-rare earth elements) material has a strong potential to enable dipole magnetic fields above 20 T in future circular particle colliders, the magnet and conductor technology needs to be developed. As part of an ongoing development to address this need, here we report on our CORC® canted cosθ magnet called C2 with a target dipole field of 3 T in a 65 mm aperture. The magnet was wound with 70 m of 3.8 mm diameter CORC® wire on machined metal mandrels. The wire had 30 commercial REBCO tapes from SuperPower Inc. each 2 mm wide with a 30 µm thick substrate. The magnet generated a peak dipole field of 2.91 T at 6.290 kA, 4.2 K. The magnet could be consistently driven into the flux-flow regime with reproducible voltage rise at an engineering current density between 400-550 A mm-2, allowing reliable quench detection and magnet protection. The C2 magnet represents another successful step towards the development of high-field accelerator magnet and CORC® conductor technologies. The test results highlighted two development needs: continue improving the performance and flexibility of CORC® wires and develop the capability to identify locations of first onset of flux-flow voltage.

African-American men have the highest incidence of and mortality from prostate cancer. Whether a biological basis exists for this disparity remains unclear. Exome sequencing (n = 102) and targeted validation (n = 90) of localized primary hormone-naïve prostate cancer in African-American men identified several gene mutations not previously observed in this context, including recurrent loss-of-function mutations in ERF, an ETS transcriptional repressor, in 5% of cases. Analysis of existing prostate cancer cohorts revealed ERF deletions in 3% of primary prostate cancers and mutations or deletions in ERF in 3% to 5% of lethal castration-resistant prostate cancers. Knockdown of ERF confers increased anchorage-independent growth and generates a gene expression signature associated with oncogenic ETS activation and androgen signaling. Together, these results suggest that ERF is a prostate cancer tumor-suppressor gene. More generally, our findings support the application of systematic cancer genomic characterization in settings of broader ancestral diversity to enhance discovery and, eventually, therapeutic applications.Significance: Systematic genomic sequencing of prostate cancer in African-American men revealed new insights into prostate cancer, including the identification of ERF as a prostate cancer gene; somatic copy-number alteration differences; and uncommon PIK3CA and PTEN alterations. This study highlights the importance of inclusion of underrepresented minorities in cancer sequencing studies. Cancer Discov; 7(9); 973-83. ©2017 AACR.This article is highlighted in the In This Issue feature, p. 920.

The COVID-19 pandemic presented enormous data challenges in the United States. Policy makers, epidemiological modelers, and health researchers all require up-to-date data on the pandemic and relevant public behavior, ideally at fine spatial and temporal resolution. The COVIDcast API is our attempt to fill this need: Operational since April 2020, it provides open access to both traditional public health surveillance signals (cases, deaths, and hospitalizations) and many auxiliary indicators of COVID-19 activity, such as signals extracted from deidentified medical claims data, massive online surveys, cell phone mobility data, and internet search trends. These are available at a fine geographic resolution (mostly at the county level) and are updated daily. The COVIDcast API also tracks all revisions to historical data, allowing modelers to account for the frequent revisions and backfill that are common for many public health data sources. All of the data are available in a common format through the API and accompanying R and Python software packages. This paper describes the data sources and signals, and provides examples demonstrating that the auxiliary signals in the COVIDcast API present information relevant to tracking COVID activity, augmenting traditional public health reporting and empowering research and decision-making.