Almost seventy percent of fire related deaths are caused by the inhalation of toxins such as CO and soot that are produced when fires become underventilated.(1) Although studies have established the importance of CO formation during underventilated burning,(2) the formation processes of CO (and soot) in underventilated fires are not well understood. The goal of the COSMIC project is to study the formation processes of CO and soot in underventilated flames. A potential way to study CO and soot production in underventilated flames is the use of inverse diffusion flames (IDFs). An IDF forms between a central air jet and a surrounding fuel jet. IDFs are related to underventilated flames because they may allow CO and soot to escape unoxidized. Experiments and numerical simulations of laminar IDFs of CH4 and C2H4 were conducted in 1-g and µ-g to study CO and soot formation. Laminar flames were studied because turbulent models of underventilated fires are uncertain. Microgravity was used to alter CO and soot pathways. A IDF literature survey, providing background and establishing motivation for this research, was presented at the 5th IWMC.(3) Experimental results from 1-g C2H4 IDFs and comparisons with simulations, demonstrating similarities between IDFs and underventilated fires, were presented at the 6th IWMC.(4) This paper will present experimental results from µ-g and 1-g IDFs of CH4 and C2H4 as well as comparisons with simulations, further supporting the relation between IDFs and underventilated flames.

The structure of laminar inverse diffusion flames (IDFs) of methane and ethylene was studied using a cylindrical co-flowing burner. Several flames of the same fuel flow-rate yet various air flow-rates were examined. Heights of visible flames were obtained using measurements of hydroxyl (OH) laser-induced fluorescence (LIF) and visible images. Polycyclic aromatic hydrocarbon (PAH) LIF and soot laser-induced incandescence (LII) were also measured. In visible images, radiating soot masks the blue region typically associated with the flame height in normal diffusion flames (NDFs). Increased air flow-rates resulted in longer flames. PAH LIF and soot LII indicated that PAH and soot are present on the fuel side of the flame and that soot is located closer to the reaction zone than PAH. Ethylene flames produced significantly higher PAH LIF and soot LII signals than methane flames, which is consistent with the sooting propensity of

Measurements of line-of-sight laser extinction in a co-annular ethylene-air laminar inverse diffusion flame (IDF) were made to determine soot concentration. Extinction has frequently been used in the literature to measure soot concentration in normal diffusion flames (NDFs), but it has rarely been applied to IDFs. A coflow IDF contains a primary air flow surrounded by a fuel annulus. Soot particles form on the outside of IDFs, advect upward, and eventually quench without being oxidized. It has been proposed in the literature that IDFs will produce less near-flame soot than NDFs because, for flames of comparable fuel, size and flow rates, movement of soot outward into cool regions of an IDF limits its simultaneous exposure to the high temperatures and fuel pyrolysis products needed for soot growth. A two-dimensional soot concentration map of an IDF using experimental data confirms this hypothesis by showing integrated soot volume fractions to be an order of magnitude lower than those reported for NDFs in the literature. Computer simulations of particle temperature histories in an NDF and IDF of similar height lend support to these results.

Flame heights of co-flowing cylindrical ethylene-air and methane-air laminar inverse diffusion flames were measured. The luminous flame height was found to be longer than the height of the reaction zone determined by planar laser-induced fluorescence (PLIF) of hydroxyl radicals (OH) because of luminous soot above the reaction zone. However, the location of the peak luminous signals along the centerline agreed very well with the OH flame height. Flame height predictions using Roper’s analysis for circular port burners agreed with measured reaction zone heights when using values for the characteristic diffusion coefficient and/or diffusion temperature somewhat different from those recommended by Roper. The fact that Roper’s analysis applies to inverse diffusion flames is evidence that inverse diffusion flames are similar in structure to normal diffusion flames.