We have developed and tested a novel magnetic inductive antenna for detecting and localizing quenches and flux jumps in superconducting accelerator magnets during ramping and steady-state operations. The antenna principle is based upon sensing temporal variation of the axial field gradient in the magnet bore that is specific to propagating quench. Two antenna configurations were developed and built, optimized respectively for sensing disturbances of the off-axis (for the dipole magnet) and axial (for the quadrupole magnet) gradient of the axial field. The antennas were qualified during tests of LBNL's high-field dipole, HD3b, and LARP's Nb3Sn quadrupole HQ02b. A reliable and accurate localization of quenches and flux jumps was demonstrated. Upon ramping up the magnet current, we observed peculiar dynamics of the magnetic disturbances travelling along the cable at velocities of ∼800 m/s. Also, details of slow quench propagation in the HQ02 quadrupole at a small fraction of operational current were detected and recorded.

The U.S. Magnet Development Program (MDP) collaboration is designing a utility mechanical structure for testing various high-field superconducting dipole coils. The design uses a shell-based structure concept, which allows applying preload in two steps: During a room temperature assembly and during a cool down to a cryogenic temperature. The structure is designed to accommodate various coil designs - including Nb3Sn Cosine Theta (CT) and Canted CT magnets as well as hybrid magnets with high temperature superconductor cables. Superconducting coils, enclosed by bolted pads to form an octagonal coil pack, will be inserted into a reusable yoke-shell subassembly and precisely preloaded during the assembly using a bladder-and-key technology. Due to a differential thermal contraction between an external aluminum shell and the magnet core, the coil preload increases during the cool down up to level required for 17-T excitation. Such a reusable structure will serve as a testing fixture supporting goals of the MDP program, decreasing cost and simplifying coil performance testing at different preload levels. We present a finite-element analysis of the structure preloading various coil designs and examine the predicted coil stress at each step of the magnet assembly and excitation.

Recent studies have shown that strong, alternating focusing magnets can be used to greatly increase the momentum acceptance of hadron therapy gantries. With the high gradients achievable with superconducting magnets a level of momentum acceptance can be reached which may have significant implications to medical gantries and to the introduction of superconducting technology in this area. The design of such a superconducting magnet system for a proton therapy gantry will be presented. The Canted-Cosine-Theta concept is extended to a curved magnet system generating the desired bending and alternating focusing fields for the achromatic optics. Magnetic, structural, and thermal analysis of this design is presented along with preliminary efforts towards fabrication and assembly of the curved magnet.

The ECR source magnet of the FRIB facility has been designed by the Superconducting Magnet Program at the Lawrence Berkeley National Laboratory (LBNL). The magnetic parameters are close to the VENUS magnet (sextupole-in-solenoids) operated at LBNL. The mechanical assembly concept, however, is different and uses a shell-based support structure. The main advantage of this structure is the ability to finely tune the sextupole prestress both azimuthally (by way of bladder and key technology, and axially by means of end plates. This method of structural pre-loading applies the desired compression on the sextupole coils while maintaining acceptable peak stresses. Also, bladder and key technology is a reversible assembly process allowing fast and easy coil replacement, when necessary. This paper also describes the mechanical analysis required to estimate the sextupole and solenoids preloads. The stress distribution in the windings and structural components are presented during assembly, cool-down, and magnet excitation.

The Superconducting Magnet Group, at Lawrence Berkeley National Laboratory (LBNL), has been developing a canted cosine-theta (CCT) superconducting dipole coil as well as the coil's supporting magnet structure. This contribution reports on the progress in the development of the coil's winding mandrel and its fabrication options. A comprehensive study of the coil's Lorentz forces was performed to validate the winding mandrel's "stress interception" attributes. The design of the external structure and the application of the "Bladder & Key" technology is also discussed. Additionally, the application of these studies to a curved ion-therapy CCT dipole magnet is reported.

A commercial Finite-Element-Analysis program, ANSYS®, is widely used in structural and thermal analysis. With the program's ability to include nonlinear material properties and import complex CAD files, one can generate coil geometries and simulate quench propagation in superconducting magnets. A "proof-of-principle" finite element model was developed assuming a resistivity that increases linearly from zero to its normal value at a temperature consistent with the assumed B magnetic field. More sophisticated models could easily include finer-grained coil, cable, structural, and circuit details. A quench is provoked by raising the temperature of an arbitrary superconducting element above its Tc. The time response to this perturbation is calculated using small time-steps to allow convergence between steps. Snapshots of the temperature and voltage distributions allow examination of longitudinal and turn-to-turn quench propagation, quench-front annihilation, and cryo-stability. Modeling details are discussed, and a computed voltage history was compared with measurements from a recent magnet test.